User:Jtoller7619/Mojo Stratasys 3D printer

http://www.3dvision.com/pdf/3D-printing/mojo-printer-user-guide.pdf http://www.johnewrighttechnical.com/datasheet/3dsupport/WaveWash/WaveWash%2055%20User%20Guide%20EN.pdf

specs:
Mojo builds a maximum part size of 127 x 127 x 127 mm (5 x 5 x 5 in.).

LED display indicates what is occurring:


 * green circle: Idle/Build
 * Green circle surrounded by lines: door or cover open
 * Yellow circle: User pause
 * Yellow circle surrounded by lines: Machine pause
 * Red circle: user cancel
 * Red circle surrounded by lines: failure

for picture see page 13 of the Mojo printer user guide (link provided at top of page)

3D printer software will also show icons indicating printer status:

for picture see page 14 of the Mojo printer user guide (link provided at top of page)

To print:

 * Install the modeling base by aligning the base tabs into the slots on the platen.

- platen is #6 in the drawing on page 4 of the user guide


 * Push the modeling base onto the platen making sure the base “clicks” into position.
 * Close the door
 * create cad file
 * convert CAD file to STL:

for inventor: - click on "I" icon in top left corner

-click on export

- click on CAD format

- select STL from the save as type drop down menu

 File:Tip wipe assembly.JPG|tip wipe assembly 
 * inspect tip wipe assembly if there is build up of material brush it off
 * On printer computer start Print Wizard (see page 17 of the Mojo printer user guide (link provided at top of page))
 * STL files can be added to the job by:

- Double-clicking an STL file.

- Using the drag-and-drop feature of Windows Explorer to move the file into the print window.

- By clicking the “+” sign.
 * to remove a part right click it and select remove part
 * After the part(s) have been selected, click the Print button this will send the part(s) to the computer

to print:

 File:Used plate box.JPG|after trays in used plate box are sanded they will be placed back in the same box as the unused plates. 
 * Open Mojo control panel
 * Select part
 * click print
 * when printing is complete and door is unlocked(screen will have remove part message), remove plate by lifting tab and pulling towards self
 * remove part from plate
 * place plate in used plate box
 * for more information refer to the Mojo printer user guide (link provided at top of page)


 * for trouble shooting see pages 44-48 of the Mojo printer user guide (link provided at top of page)

WAVEWASH 55 specs
http://store.javelin-tech.com/Store-Catalog/Mojo-3D-Printer/Mojo-Ecoworks-Tablets-Cleaning-Agent

http://www.johnewrighttechnical.com/datasheet/3dsupport/WaveWash/WaveWash%2055%20User%20Guide%20EN.pdf

safety:
 * students should wear eye protection and gloves while working with the solvent solution

How to use:

 File:Mojo wavewash carafe.JPG|empty carafe   File:Eco wash tablet packet.JPG|ecoworks tablet packet 
 * Power system on ( black switch on side)
 * Remove lid
 * Place EcoWorks cleaning tablet into carafe ( for labled diagram of parts see pages 5 and 6 of the WaveWash 55 user guide (link provided at top of page))
 * Place printed parts into carafe
 * Fill carafe with clean hot water to cover parts by 3 inches ( make sure water remains at least an inch below lid)
 * Place lid on carafe
 * Place carafe on system base
 * Press start button
 * Wait for cleaning cycle to complete (takes about 8 hours)
 * lift lid slightly and drain liquid
 * refill with warm water to rinse for approximately 5 minutes
 * lift lid slightly and drain liquid
 * remove and dry parts