User:Mkamara9540/ENES-100/project 2

Week1 project2
task programming the aduin to accept messages from the CAN BUS upload video of arduino and CAN BUS talking connecting to the arduino and CAN BUS to get CAN DATA NEXT STEPSː ːfiguring out how to connect CAN BUS to car's radio

Week2 project2
TaskːFind ways to connect simulate vechicle with SEED CAN Bus that is recognized by the ODE Scanner


 * Found method to hook SEED CAN Bus shield to a car can bus wires controlling a radioː
 * link showing seeed CAN Bus connected to Jeep Wrangler 2010
 * https://www.youtube.com/watch?v=UM2hFBiUOqw&feature=youtu.be- link showing video of what would happen to arduino/CAN bus shield when the wires are disconnected from one set
 * https://www.youtube.com/watch?v=nWhZG1no-8E&feature=youtu.be- limk showing the result of arduino when you turn off the "on/off" switch

Next stepsː
 * use OBD II adapter for arduino
 * use every components and steps that come with OBD II adapter, such as connecting adaptor's TX to arduino's RX(D0) and adaptor's RX to arduino's TX (D1)

Task
upload videos of different experiments with transmitter and receiver (Arduino/CAN bus shield)

https://www.youtube.com/watch?v=B8qlDnclEgI&feature=youtu.be video link of Arduino/CAN bus before any experiment

https://www.youtube.com/watch?v=Q1eNjTpIhnA&feature=youtu.be video link of two arduino/can bus talking to each other with a serial monitor

https://www.youtube.com/watch?v=m7D6YksDBRI&feature=youtu.be video link of low voltage wire disconnected from the receiver

https://www.youtube.com/watch?v=oUnS8gZ0fx4&feature=youtu.be video link of low voltage wire disconnected from the transmitter

https://www.youtube.com/watch?v=M0YvvGeOSyc&feature=youtu.be video link of USB CORD disconnected from the transmitter

https://www.youtube.com/watch?v=CBLZ-WF_r9k video link of USB CORD disconnected from the receiver

https://www.youtube.com/watch?v=59nCpLflV38 video of both voltage wires (low/high) disconnected from the transmitter

https://www.youtube.com/watch?v=bBXLNCOXiRo&feature=youtu.be video link of both voltage (low/high) disconnected from the receiver

https://www.youtube.com/watch?v=gOWqghkzMxw&feature=youtu.be video link of high voltage wire disconnected from the transmitter

https://www.youtube.com/watch?v=oTfYcx2w7ec&feature=youtu.be video link of high voltage wire disconnected from the receiver

https://www.youtube.com/watch?v=kLyA4VpVfaY&feature=youtu.be switch off the "off/on" switch on both the transmitter and receiver

Next Steps
-use OBD adaptor ground wire to connect to arduino ground

-run extra wire from arduino vin to OBD adaptor vin

-use the wall adaptor charger for the arduino rather than the USB CORD for our experiment

task
• had Arduino to power up the OBD connector

• had CAN bus's female into the male pin of Arduino to power up the OBD connector

https://www.youtube.com/watch?v=Pa4B4UgBS3I&feature=youtu.be this is the link of arduino powering the OBD connector

https://www.youtube.com/watch?v=NgMnR2S9kKI&feature=youtu.be link of extra wires connected to CAN bus's female pin through the male pin of arduino to power up the OBD connector

next steps
• figure out how to connect the OBD connector to ECU board to get information